Glass Splashback Installation Derby
Free Consultation
01332-529933
A glass splashback is one of the quickest ways to change the look of a kitchen without pulling the rest of it apart, which is why it's the finish our fitters get asked about most once people have priced up re-tiling instead. Derby Kitchen Fitter measures, cuts and fits toughened glass to order from our workshop on Stenson Road in Sunny Hill, working around whatever is already on your wall rather than a standard panel size.
A lot of the walls we template for aren't flat behind the hob. Victorian terraces around Derby and the stone-built cottages out towards Wirksworth and Bakewell often have a wall that's out of true by several millimetres from top to bottom, and a rigid glass panel will show every bit of that gap if it isn't measured for properly. Because the same crew that templates your splashback can also move a socket, skim a patch of uneven wall or match a paint colour exactly, you're not left waiting on a second tradesperson to finish the job off before the glass can go up.
Glass Splashback vs Tiled Splashback
| Glass Splashback | Tiled Splashback | |
|---|---|---|
| Cleaning | One wipe with a cloth, no grout lines to scrub | Grout needs regular scrubbing and discolours over time |
| Heat resistance | Toughened glass rated to withstand high temperatures behind hobs | Tiles cope with heat but grout close to a hob can crack or crumble |
| Fitting time | Usually a single day once the glass has been manufactured to size | Several days once tiling, grouting and drying time are included |
| Colour and finish | Any colour match, a printed image, or a mirror finish | Limited to whichever tile ranges are in stock or on order |
| Sockets and switches | Cut precisely as one piece so fittings sit flush | Tiles are cut individually around fittings, leaving more visible joints |
| Typical cost | From around £200 for a small area up to £1,000+ for a large, complex kitchen | Varies with tile choice and labour, often a similar range for a comparable area |
Why a Kitchen Fitting Team Cuts Your Glass, Not a Glazier
Glass splashbacks are ordered as one fixed panel, so there's no trimming a corner on site if the template is out. That's why we send the same team that laser-templates our stone worktops to measure yours, rather than a glazier working from a tape measure and a spirit level against an uneven wall. If you want an exact colour match rather than a stock shade, that work goes to the same spray finishers who colour-match kitchen doors and cabinet ends to ranges like Farrow & Ball and Little Greene, so the paint behind your glass is mixed to a proper reference rather than eyeballed against a swatch card. Any socket that needs moving first is handled by a Part P registered electrician who issues a proper certificate for the work, and if the wall itself needs skimming flat before the glass goes up, that's done by our own plasterers rather than a quick filler-and-sand job squeezed in before the panel arrives. The old splashback or tiles that come off your wall leave with us as a registered waste carrier, so you're not left with a skip's worth of rubble to sort out afterwards.
Templating and Fitting Around Derby, Wirksworth and the Peak Fringe
Most of our splashback work is in Derby itself, from the Victorian terraces around Normanton and Alvaston to the newer kitchens going into Chellaston and Mickleover, with panels cut and edge-finished at our workshop on Stenson Road in Sunny Hill before they ever reach your kitchen. We cover the same towns we fit full kitchens in - Belper, Duffield, Ripley, Heanor, Ilkeston, Long Eaton and Chesterfield among them. Out towards Wirksworth, Matlock and Bakewell the templating stage usually takes a little longer, because older stone walls finished in lime plaster rarely run flat, and we'd rather scribe the panel edge to the actual surface on site than force a glass sheet against a wall it doesn't fit. Swadlincote, Alfreton, Dronfield, Buxton and the Nottingham side of the county are also within reach for a survey and fit.
Frequently Asked Questions
Why Choose Glass Splashbacks for Your Kitchen?
Glass splashbacks have become really popular for Derby homeowners who want something special for their kitchens. And it's not hard to see why! Unlike tiles with grout lines that trap dirt and grime, glass splashbacks give you a smooth, seamless surface that's dead easy to clean. As a leading Interior Construction Contractor Derby, we've installed hundreds of splashbacks in homes across Derbyshire. Our customers love how glass splashbacks brighten up their kitchens and protect their walls at the same time. The benefits of our glass splashbacks include: Super easy to clean - just wipe with a cloth, no scrubbing grout lines! Heat resistant - our toughened glass stands up to high temperatures Totally waterproof and stain resistant - perfect behind sinks and cookers Reflects light to make your
How Much Do Glass Splashbacks Cost in Derby?
The cost of glass splashback installation in Derby varies depending on several factors: Size of the splashback - larger pieces naturally cost more Complexity of the shape - unusual shapes require more work Number of cutouts needed for sockets and switches Type of glass - coloured, printed, mirrored etc. Installation requirements - some walls need more prep work As a rough guide, prices for a standard coloured glass splashback start from around £200 for a small area behind a hob, up to £1,000+ for a large, complex kitchen installation. We always provide a detailed, no-obligation quote after our initial survey, so you'll know exactly what costs to expect before you commit.
Are Glass Splashbacks Heat Resistant for Use Near Cookers?
This is one of the questions we get most often! The answer is yes - our toughened glass splashbacks are perfectly safe to use behind hobs and cookers. All the glass we use for kitchen splashbacks is toughened (sometimes called tempered) to British Safety Standards. This makes it heat resistant up to 220°C - much higher than the temperature your walls would normally reach, even behind a busy cooker. For gas hobs, we recommend leaving a small gap (usually about 50-100mm) between the hob and the splashback, just as an extra precaution. For induction or electric hobs, the splashback can usually be fitted right up to the edge of the cooker.
Can Glass Splashbacks Be Cut for Sockets and Switches?
Yes, we can create precise cutouts for any sockets, switches or other fixtures on your walls. During our measuring process, we'll note the exact position of all electrical points. Our cutting equipment allows us to make these cutouts with perfect accuracy, so everything fits back into place seamlessly after installation. We can also reposition sockets before installation if needed - our electricians are fully qualified and can move sockets to more convenient locations or add new ones as part of the project.
How Are Glass Splashbacks Attached to Walls?
Our glass splashbacks are attached using a special high-strength adhesive designed specifically for this purpose. This adhesive: Creates a permanent, secure bond Allows for slight movement (important to prevent stress on the glass) Is heat resistant Won't deteriorate over time Before applying the adhesive, we prepare your walls thoroughly to ensure a perfect surface. This might involve removing old tiles, filling holes, or smoothing uneven areas. For a typical installation: We clean and prepare the wall surface Apply the adhesive in a specific pattern Carefully position the glass Use temporary supports while the adhesive sets Seal around the edges with a matching silicone
Can Glass Splashbacks Be Installed Over Existing Tiles?
Yes, in many cases we can install glass splashbacks directly over existing tiles, saving you the mess and expense of removing them. Before we do this, we'll check that: The existing tiles are securely fixed to the wall The surface is reasonably flat and even There's no damage or dampness issues Installing over tiles can make the process quicker and cleaner, with less disruption to your kitchen. It's particularly good if you're after a quick kitchen makeover rather than a full renovation.
How Long Does the Glass Splashback Installation Process Take?
From your initial enquiry to completed installation, the typical timeline is: Initial consultation and survey : 1-2 days to arrange Quote and design finalisation : 1-3 days Manufacturing : 7-14 days depending on complexity Installation : Usually completed in a single day So in total, you could have your new glass splashback installed within 2-3 weeks of your first call to us. For urgent projects, we might be able to work to a faster schedule - just let us know your timeframe when you get in touch.
Why Choose Derby Kitchen Fitter for Your Glass Splashback Installation?
When it comes to glass splashback installation in Derby, we believe our service is second to none. Here's why our customers choose us: Experience : We've been fitting kitchens and splashbacks in Derby for over 10 years Quality materials : We only use the best quality toughened glass for safety and durability Skilled craftsmen : Our installers are fully trained and experienced Attention to detail : We take pride in the little things that make a big difference Complete service : From initial design to final installation, we handle everything Competitive pricing : Quality doesn't have to cost the earth Excellent aftercare : We're always here if you need us after installation Don't just take our word for it - check out our reviews and testimonials from happy customers across Derby and Derbyshi
Ready to Transform Your Kitchen with a Beautiful Glass Splashback?
If you're interested in adding a glass splashback to your kitchen, we'd love to help. Getting started is easy: Call us on 01332-325444 Use our online contact form to request a callback We offer free, no-obligation consultations and quotes, so you've got nothing to lose by getting in touch. Don't forget to ask about our current special offers - we frequently run promotions on glass splashback installation when booked alongside our other kitchen services.
What Is the Difference Between Toughened and Tempered Glass?
Actually, they're the same thing! "Toughened" is the term usually used in the UK, while "tempered" is more common in America. Both refer to glass that's been heat-treated to make it stronger and safer.
Can I Install a Glass Splashback Myself?
While DIY installation is possible, we don't recommend it. Glass splashbacks are heavy, fragile until installed, and need special handling. Professional installation ensures a perfect finish and eliminates risks of costly mistakes.
How Thick Should My Glass Splashback Be?
We typically use 6mm toughened glass for most kitchen splashbacks. This provides the perfect balance of strength and weight. For very large areas, we might recommend 8mm or 10mm glass for additional structural integrity.
Can You Match My Existing Kitchen Colour?
Yes! We can colour-match to any paint brand or sample you provide. We'll show you samples before manufacturing to ensure you're happy with the colour match. Design - Supply - Installation - Project Management Derby Kitchen Fitter One-Stop-Shop For Everything Kitchens and More! 01332-325444
Ready for a New Glass Splashback in Derby?
Book a free, no-obligation quote for your Derby glass splashback installation. Call Derby Kitchen Fitter on 01332-529933 or email info@derbykitchenfitter.co.uk to get started.
Two decades fitting • 5-Year Guarantee • Part P Approved
Quick Free Estimate - No Obligation
Fully Insured • Response within 15 mins
🔒 Your details are safe with us. No spam, ever.